PIC16F877A-I/P Microchip MCU

Features:
High-Performance RISC CPU:
• Only 35 single-word instructions to learn
• All single-cycle instructions except for program branches, which are two-cycle.
• Operating speed:
DC – 20 MHz clock input DC–200 ns instruction cycle
• Up to 8K x 14 words of Flash Program Memory, Up to 368 x 8 bytes of Data Memory (RAM), Up to 256 x 8 bytes of EEPROM Data Memory
• Pinout compatible to other 28-pin or 40/44-pin PIC16CXXX and PIC16FXXX microcontrollers

Peripheral Features:
• Timer0: 8-bit timer/counter with 8-bit prescaler
• Timer1: 16-bit timer/counter with prescaler, can be incremented during Sleep via external crystal/clock
• Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler
• Two Capture, Compare, PWM modules
- Capture is 16-bit, max. resolution is 12.5 ns
- Compare is 16-bit, max. resolution is 200 ns
- PWM max. resolution is 10-bit
• Synchronous Serial Port (SSP) with SPI™ (Master mode) and I2C™ (Master/Slave)
• Universal Synchronous Asynchronous Receiver Transmitter (USART/SCI) with 9-bit address detection
• Parallel Slave Port (PSP) – 8 bits wide with external RD, WR and CS controls (40/44-pin only)
• Brown-out detection circuitry for Brown-out Reset (BOR)

Analog Features:
• 10-bit, up to 8-channel Analog-to-Digital Converter (A/D)
• Brown-out Reset (BOR)
• Analog Comparator module with:
- Two analog comparators
- Programmable on-chip voltage reference (VREF) module
- Programmable input multiplexing from device inputs and internal voltage reference
- Comparator outputs are externally accessible

Special Microcontroller Features:
• 100,000 erase/write cycle Enhanced Flash program memory typical
• 1,000,000 erase/write cycle Data EEPROM memory typical
• Data EEPROM Retention > 40 years
• Self-reprogrammable under software control
• In-Circuit Serial Programming™ (ICSP™) via two pins
• Single-supply 5V In-Circuit Serial Programming
• Watchdog Timer (WDT) with its own on-chip RCoscillator for reliable operation
• Programmable code protection
• Power saving Sleep mode
• Selectable oscillator options
• In-Circuit Debug (ICD) via two pins

CMOS Technology:
• Low-power, high-speed Flash/EEPROM technology
• Fully static design
• Wide operating voltage range (2.0V to 5.5V)
• Commercial and Industrial temperature ranges
• Low-power consumption

TMS4416-15NL 20-Pin DIP

Feature:
- Dynamic RAM
- 16,384 Word by 4 Bit
- TTL compatible 150ns
- 3-State Unlatched Outputs
- Single +5V Supply (10% tolerance)
- Low refresh periode 4ms
- Operating Power Dissipation 200mW
- Standby Power Dissipation 17.5mW

PIC18F4585-I/P Microchip MCU

FEATURE:
------------
- Package PDIP40
- Packaging tube
- Lead Spacing 2.54mm
- Op.Temperature -40 ~ 85°C
- Series PIC18
- Architecture 8-bit
- Speed 40MHz/10MIPS
- Internal Oscillator 8MHz,32kHz
- Memory Type PIC18F4585
- Program Memory 24k x 16
- EEPROM 1024
- RAM 3328
- Self Program Yes
- I/O 36
- A/D 11x 10-bit
- Interfaces 0 -UART , 1 -A/E/USART , 0 -SPI , 0 -I2C , 1 -MSSP(SPI/I2C) , 0 -SSP(SPI/I2C)
- Timers 1x 8-bit ,3x 16-bit
- Op.Voltage 2V ~ 5.5V
- Stack 31-level
- Power-On Reset Yes
- Brown-Out Reset
- Watchdog Yes
- Max. Clamp Current ±20mA
- Max. Sink/Source ±25mA

PIC18F4580-I/P Microchip MCU

- Package PDIP40
- Lead Spacing 2.54mm
- Op.Temperature -40 ~ 85°C

FEATURE:
------------
- Architecture 8-bit
- Speed 40MHz/10MIPS
- Internal Oscillator 8MHz,32kHz
- Memory Type PIC18F4580
- Program Memory 16k x 16
- EEPROM 256
- RAM 1536
- Self Program Yes
- I/O 36
- A/D 11x 10-bit
- Interfaces 0 -UART , 1 -A/E/USART , 0 -SPI , 0 -I2C , 1 -MSSP(SPI/I2C) , 0 -SSP(SPI/I2C)
- Timers 1x 8-bit ,3x 16-bit
- Op.Voltage 2V ~ 5.5V
- Stack 31-level
- Power-On Reset Yes
- Brown-Out Reset
- Watchdog Yes
- Max. Clamp Current ±20mA
- Max. Sink/Source ±25mA

PIC18F4455-I/P Microchip MCU

FEATURE:
-Packaging tube
-Lead Spacing 2.54mm
-Op.Temperature -40 ~ 85°C
-Series PIC18
-Architecture 8-bit
-Speed 48MHz/12MIPS
-Internal Oscillator 8MHz, 32kHz
-Memory Type PIC18F4455
-Program Memory 12k x 16
-EEPROM 256
-RAM 2048
-Self Program Yes
-I/O 35
-A/D 13x 10-bit
-Interfaces 0 -UART , 1 -A/E/USART , 0 -SPI , 0 -I2C , 1 -MSSP(SPI/I2C)
-Timers 1x 8-bit ,3x 16-bit , 0 - 32-bit
-Op.Voltage 2V ~ 5.5V
-Stack 31-level
-Power-On Reset Yes
-Brown-Out Reset
-Watchdog Yes
-Max. Clamp Current ±20mA
-Max. Sink/Source ±25mA

PIC18F2525-I/SP Microchip MCU

28-Pin Enhanced Flash Microcontrollers
with 10-Bit A/D and nanoWatt Technology
--------------------------------------------

Power Managed Modes:
• Run: CPU on, peripherals on
• Idle: CPU off, peripherals on
• Sleep: CPU off, peripherals off
• Idle mode currents down to 2.5 ¼A typical
• Sleep mode current down to 100 nA typical
• Timer1 Oscillator: 1.8 ¼A, 32 kHz, 2V
• Watchdog Timer: 1.4 ¼A, 2V typical
• Two-Speed Oscillator Start-up

Flexible Oscillator Structure:
• Four Crystal modes, up to 40 MHz
• 4x Phase Lock Loop (PLL) – available for crystal and internal oscillators)
• Two External RC modes, up to 4 MHz
• Two External Clock modes, up to 40 MHz
• Internal oscillator block:
- 8 user selectable frequencies, from 31 kHz to 8 MHz
- Provides a complete range of clock speeds from 31 kHz to 32 MHz when used with PLL
- User tunable to compensate for frequency drift
• Secondary oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor
- Allows for safe shutdown if peripheral clock stops

Peripheral Highlights:
• High-current sink/source 25 mA/25 mA
• Three programmable external interrupts
• Four input change interrupts
• Up to 2 Capture/Compare/PWM (CCP) modules, one with Auto-Shutdown (28-pin devices)
• Enhanced Capture/Compare/PWM (ECCP) module (40/44-pin devices only):
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-Shutdown and Auto-Restart

Peripheral Highlights (Continued):
• Master Synchronous Serial Port (MSSP) module supporting 3-wire SPI™ (all 4 modes) and I2C™
Master and Slave modes
• Enhanced Addressable USART module:
- Supports RS-485, RS-232 and LIN 1.2
- RS-232 operation using internal oscillator block (no external crystal required)
- Auto-Wake-up on Start bit
- Auto-Baud Detect
• 10-bit, up to 13-channel Analog-to-Digital Converter module (A/D):
- Auto-acquisition capability
- Conversion available during Sleep
• Dual analog comparators with input multiplexing
• Programmable 16-level High/Low-Voltage
Detection (HLVD) module:
- Supports interrupt on High/Low-Voltage Detection
Special Microcontroller Features:
• C compiler optimized architecture:
- Optional extended instruction set designed to
optimize re-entrant code
• 100,000 erase/write cycle Enhanced Flash
program memory typical
• 1,000,000 erase/write cycle Data EEPROM
memory typical
• Flash/Data EEPROM Retention: 100 years typical
• Self-programmable under software control
• Priority levels for interrupts
• 8 x 8 Single Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 131s
• Single-supply 5V In-Circuit Serial
Programming™ (ICSP™) via two pins
• In-Circuit Debug (ICD) via two pins
• Wide operating voltage range: 2.0V to 5.5V
• Programmable Brown-out Reset (BOR) with
software enable option.

PIC18F4553-I/P Microchip MCU

40-Pin High-Performance, Enhanced Flash, USB
Microcontrollers with 12-Bit A/D and nanoWatt Technology.
---------------------------------------------
Universal Serial Bus Features:
• USB V2.0 Compliant
• Low Speed (1.5 Mb/s) and Full Speed (12Mb/s)
• Supports Control, Interrupt, Isochronous and Bulk Transfers
• Supports up to 32 Endpoints (16 bidirectional)
• 1-Kbyte Dual Access RAM for USB
• On-Chip USB Transceiver with On-Chip Voltage Regulator
• Interface for Off-Chip USB Transceiver
• Streaming Parallel Port (SPP) for USB Streaming Transfers (40/44-pin devices only)

Power-Managed Modes:
• Run: CPU On, Peripherals On
• Idle: CPU Off, Peripherals On
• Sleep: CPU Off, Peripherals Off
• Idle mode Currents Down to 5.8 ¼A Typical
• Sleep mode Currents Down to 0.1 ¼A Typical
• Timer1 Oscillator: 1.1 ¼A Typical, 32 kHz, 2V
• Watchdog Timer: 2.1 ¼A Typical
• Two-Speed Oscillator Start-up

Special Microcontroller Features:
• C Compiler Optimized Architecture with Optional Extended Instruction Set
• 100,000 Erase/Write Cycle Enhanced Flash Program Memory Typical
• 1,000,000 Erase/Write Cycle Data EEPROM Memory Typical
• Flash/Data EEPROM Retention: > 40 Years
• Self-Programmable under Software Control
• Priority Levels for Interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
- Programmable period from 41 ms to 131s
• Programmable Code Protection
• Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via Two Pins
• In-Circuit Debug (ICD) via Two Pins
• Optional Dedicated ICD/ICSP Port (44-pin TQFP package only)
• Wide Operating Voltage Range (2.0V to 5.5V)

Flexible Oscillator Structure:
• Four Crystal modes, Including High-Precision PLL for USB
• Two External Clock modes, up to 48 MHz
• Internal Oscillator Block:
- 8 user-selectable frequencies, from 31 kHz to 8 MHz
- User-tunable to compensate for frequency drift
• Secondary Oscillator using Timer1 @ 32 kHz
• Dual Oscillator Options allow Microcontroller and USB module to Run at Different Clock Speeds
• Fail-Safe Clock Monitor:
- Allows for safe shutdown if any clock stops

Peripheral Highlights:
• High-Current Sink/Source: 25 mA/25 mA
• Three External Interrupts
• Four Timer modules (Timer0 to Timer3)
• Up to 2 Capture/Compare/PWM (CCP) modules:
- Capture is 16-bit, max. resolution 5.2 ns (TCY/16)
- Compare is 16-bit, max. resolution 83.3 ns (TCY)
- PWM output: PWM resolution is 1 to 10-bits
• Enhanced Capture/Compare/PWM (ECCP) module:
- Multiple output modes
- Selectable polarity
- Programmable dead time
- Auto-shutdown and auto-restart
• Enhanced USART module:
- LIN bus support
• Master Synchronous Serial Port (MSSP) module supporting 3-wire SPI (all 4 modes) and I2C™ Master and Slave modes
• 12-Bit, up to 13-Channel Analog-to-Digital Converter module (A/D) with Programmable Acquisition Time
• Dual Analog Comparators with Input Multiplexing

PIC18F4525-I/P Microchip MCU

40-Pin High-Performance, Enhanced Flash, USB Microcontrollers with 12-Bit A/D and nanoWatt Technology.
---------------------------------------

Universal Serial Bus Features:
• USB V2.0 Compliant
• Low Speed (1.5 Mb/s) and Full Speed (12Mb/s)
• Supports Control, Interrupt, Isochronous and Bulk Transfers
• Supports up to 32 Endpoints (16 bidirectional)
• 1-Kbyte Dual Access RAM for USB
• On-Chip USB Transceiver with On-Chip Voltage Regulator
• Interface for Off-Chip USB Transceiver
• Streaming Parallel Port (SPP) for USB Streaming Transfers (40/44-pin devices only)

Power-Managed Modes:
• Run: CPU On, Peripherals On
• Idle: CPU Off, Peripherals On
• Sleep: CPU Off, Peripherals Off
• Idle mode Currents Down to 5.8 ¼A Typical
• Sleep mode Currents Down to 0.1 ¼A Typical
• Timer1 Oscillator: 1.1 ¼A Typical, 32 kHz, 2V
• Watchdog Timer: 2.1 ¼A Typical
• Two-Speed Oscillator Start-up

Special Microcontroller Features:
• C Compiler Optimized Architecture with Optional Extended Instruction Set
• 100,000 Erase/Write Cycle Enhanced Flash Program Memory Typical
• 1,000,000 Erase/Write Cycle Data EEPROM Memory Typical
• Flash/Data EEPROM Retention: > 40 Years
• Self-Programmable under Software Control
• Priority Levels for Interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
- Programmable period from 41 ms to 131s
• Programmable Code Protection
• Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via Two Pins
• In-Circuit Debug (ICD) via Two Pins
• Optional Dedicated ICD/ICSP Port (44-pin TQFP package only)
• Wide Operating Voltage Range (2.0V to 5.5V)

Flexible Oscillator Structure:
• Four Crystal modes, Including High-Precision PLL for USB
• Two External Clock modes, up to 48 MHz
• Internal Oscillator Block:
- 8 user-selectable frequencies, from 31 kHz to 8 MHz
- User-tunable to compensate for frequency drift
• Secondary Oscillator using Timer1 @ 32 kHz
• Dual Oscillator Options allow Microcontroller and USB module to Run at Different Clock Speeds
• Fail-Safe Clock Monitor:
- Allows for safe shutdown if any clock stops

Peripheral Highlights:
• High-Current Sink/Source: 25 mA/25 mA
• Three External Interrupts
• Four Timer modules (Timer0 to Timer3)
• Up to 2 Capture/Compare/PWM (CCP) modules:
- Capture is 16-bit, max. resolution 5.2 ns (TCY/16)
- Compare is 16-bit, max. resolution 83.3 ns (TCY)
- PWM output: PWM resolution is 1 to 10-bits
• Enhanced Capture/Compare/PWM (ECCP) module:
- Multiple output modes
- Selectable polarity
- Programmable dead time
- Auto-shutdown and auto-restart
• Enhanced USART module:
- LIN bus support
• Master Synchronous Serial Port (MSSP) module supporting 3-wire SPI (all 4 modes) and I2C™ Master and Slave modes
• 12-Bit, up to 13-Channel Analog-to-Digital Converter module (A/D) with Programmable Acquisition Time
• Dual Analog Comparators with Input Multiplexing